Exactly How to Remove and Change a Tub.
Exactly How to Remove and Change a Tub.
Blog Article
We have found this great article involving How to Install a Bathtub Yourself below on the net and felt it made sense to share it with you on this page.
Setting up a tub isn't precisely rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily available, the project can move speedily; if you need to open a wall to remove the old tub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub as well as set in the new one. See to it you have actually certified yourself for the job and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly assist you install a new bathtub in your washroom if you have actually currently purchased a new tub and do not require to alter the plan of your previous water supply pipelines.
Your devices as well as material list need to make up the following:
Planning for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will certainly come from the pipes. When the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Utilizing the two wooden boards under its feet, put the tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other faucet.
Turn on the supply of water and check all joints and also brand-new pipework for leaks and tighten them if required. Fill the bathtub as well as likewise check the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind should be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to enable the movement experienced when the tub remains in use. The sealant can break relatively very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up about Installing A Bathtub from a friend on a different web page. Appreciated our content? Please share it. Let others find it. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request A Quote Report this page